The basic design is made from the point of view of machine-operator and is user friendly. The print view and inspection is made easy by providing peculiar view angle for that purpose. Oil-dipped Helical Spur gear box for the transmission makes the machine run smoothly and silently. The air circulation through silent blowers makes the efficiency of the print drying faster and with less pressure on the substrate, reduced noise, and less electrical power.

The initial tasks like loading of cylinders, loading of rolls, register synchronization are made easy. Once printed cylinders can be reloaded and printed with out going through much of the register synchronization tasks and avoids wastage of substrate.  

Distributed Control Panel : In normal machines the electrical controls of different drives are placed on a control panel which is separated from the machine and placed and the back of the operator side. The Rotogravure Printing Machine are very long in size, the operator has to come to the control panel for every operation of the control like on /off drives to boost up its power and down and the likewise operations. Similarly on emergency the operator has to run to the control panel to take immediate action. In Hyden Machine, the control panel is distributed through each printing unit and winding station. Almost all operations can be done from any control panel because clone switches are given for almost all operations. The operator can do any operation from any point where the operator is standing just by a stretch of hand.

The built-in distributed control panels are extremely comfortable for the operators. Almost all the basic operations on run-time can be done from any of the panel attached to each printing units. The operator can on / off any drive like winding drive, main-drive, dryer-air-circulators, lights etc., increase / decrease the winding torque, speed of main-drive etc., adjust web alignment etc., from any control panel. Power distribution is from very safe buss-bars supported by high quality MCB and circuit terminators. The electrical equipment like dimmer state, rectifiers etc. are isolated from machine and are enclosed in separate cabin placed suitably away from operation side. Necessary pilot lamps are provided so that the status of the machine and switches can be ascertained at any point of time.

Optional Accessories : 

Web Tension Controller : Micro processor controlled Web Tension Controller is typical attachment for accurate maintenance of print registration. Irrespective of the feed roll size the tension of the web will be maintained uniformly through out printing session using electronic tension sensors. Micro computer based electronic system assure the accuracy of the operation.

Web Aligner : The attachment can be mounted at the feed section and/or at the winding section. If attached at the feed section, it will assure the ahgnment of the feed rolls even if the feed roll is slipped or is not properly wound for use in printing machines. One edge of the feed film is sensed by air sensors (pneumatically) or by electronic light sensors and the feed roll is aligned and adjusted to the main web line. If it is fitted to the winding section, it will assure the perfect wound rolls in the out put, even if the feed rolls are defective in winding, or if some operational mistake occurred so that it may vitiates the proper winding. It will help the subsequent use of the printed rolls in automatic packing machines.

Micro processor Controlled Automatic Register Controls are available as optional accessory. This eliminates the viewing error at high speed printing and assures the accurate register of all colours resulting very high quality print out put.

Slitting Attachment : To slit feed roll or printed roll into smaller rolls. Can be attach to the winding station of the printing machine.

Lamination attachment : To laminate two or three layers of film, foil or paper together using suitable adhesive. For coating adhesive the printing unit is used and separate nipping and queering attachments are made into the machine to make the operation possible. This reduces the factory space and cost considerably if separate machines are provided for printing and lamination.

Split ability of the machine : Hyden printing machine can be split into two to act as two separate printing machines. Thus on a six colours printing machine we can do either a single colour and a five colour job simultaneously OR a two colour and four colour job OR two three colour jobs simultaneously. The splitting operation is made very simple and requires only few minutes to make the machine ready for doing two print jobs and viz.
This enable the machine to give double output.

Universal Reversibility : The machine is universally reversible to print on both side of the printing format. To print on Poly film tubes to make poly bags both side printing is necessary. The available printing units can be separated in any configuration to reverse for the other side printing. The adjustments to reverse the machine convenient to print on both sides is well designed so that the operation will take only very little time.

Different attachment can be mounted on Hyden Printing Machine for specific purposes. These attachments reduce the cost if separate machines are provided for that purposes.

General specifications :

EXTRA ATTACHMENTS NOT INCLUDED IN COST :
1. Required floor length - 15 Meters for convenient operation
2. Machine Height - 2.5 Meters
3. Machine Width - 2.5 Meters